FEM-Based Analysis of Interference Fit for High-Precision Mechanical Assemblies
Keywords:
interference fit, thick-walled cylinder theory, Finite Element MethodAbstract
This study presents an interference fit study that supports the design and evaluation of press-fit assemblies. The simulation model is based on the Thick-Walled Cylinder Theory (TCT) to accurately predict contact pressure, pressing force, and stress distribution during assembly and disassembly. The shaft-bearing assembly is machined with high precision for experimentation. The results show good agreement between the FEM simulation and the theoretical stress distribution, confirming the mechanical behavior of the interference fit. Experimental verification of the pressing force is also performed and compared with the simulation, showing consistent trends. The simulation model helps evaluate the assembly performance in different tolerance and coefficient of friction domains, providing a practical solution for high-precision mechanical assemblies.
References
[1] Y. Zhang, B. McClain, and X. J. I. J. o. M. S. Fang, "Design of interference fits via finite element method," vol. 42, no. 9, pp. 1835-1850, 2000.
[2] X. Wang, Z. Lou, X. Wang, and C. J. J. o. M. P. T. Xu, "A new analytical method for press-fit curve prediction of interference fitting parts," vol. 250, pp. 16-24, 2017.
[3] G. Marcuccio, E. Bonisoli, S. Tornincasa, J. E. Mottershead, E. Patelli, and W. J. T. J. o. S. A. f. E. D. Wang, "Image decomposition and uncertainty quantification for the assessment of manufacturing tolerances in stress analysis," vol. 49, no. 8, pp. 618-631, 2014.
[4] G.-M. Yang, J. C. Coquille, J. F. Fontaine, M. J. I. j. o. S. Lambertin, and Structures, "Influence of roughness on characteristics of tight interference fit of a shaft and a hub," vol. 38, no. 42-43, pp. 7691-7701, 2001.
[5] A. P. Raj, A. Bhatti, and P. J. P. o. t. I. o. M. E. Dhanish, Part J: Journal of Engineering Tribology, "Combined effect of cylindricity, roundness and roughness on axial load-carrying ability of interference fits," vol. 234, no. 11, pp. 1697-1711, 2020.
[6] G. Biron, A. Vadean, L. J. S. Tudose, and m. optimization, "Optimal design of interference fit assemblies subjected to fatigue loads: A sequential approximate multi-objective optimization approach," vol. 47, pp. 441-451, 2013.
[7] N. L. J. S. Pedersen and m. optimization, "On optimization of interference fit assembly," vol. 54, pp. 349-359, 2016.
[8] E. Bonisoli, G. Marcuccio, S. J. M. S. Venturini, and S. Processing, "Interference fit estimation through stress-stiffening effect on dynamics," vol. 160, p. 107919, 2021.
[9] X. Wang, Z. Lou, X. Wang, X. Hao, and Y. J. P. o. t. I. o. M. E. Wang, Part C: Journal of Mechanical Engineering Science, "Prediction of stress distribution in press-fit process of interference fit with a new theoretical model," vol. 233, no. 8, pp. 2834-2846, 2019.
[10] F. Lanoue, A. Vadean, B. J. S. M. P. Sanschagrin, and Theory, "Finite element analysis and contact modelling considerations of interference fits for fretting fatigue strength calculations," vol. 17, no. 10, pp. 1587-1602, 2009.
[11] H. Boutoutaou, M. Bouaziz, and J.-F. J. I. j. o. m. s. Fontaine, "Modelling of interference fits with taking into account surfaces roughness with homogenization technique," vol. 69, pp. 21-31, 2013.
[12] S. P. Timoshenko and J. M. Gere, Theory of elastic stability. Courier Corporation, 2009.
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Minh Nhat Truong
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
This is an open access article distributed under the terms of the CC BY-NC-SA 4.0, which permits copying, redistributing, remixing, transformation, and building upon the material in any medium so long as the original work is properly cited.
